Raspberry Pi 4 Model B provides desktop PC performanceIt has 4GB of RAM, a faster 64-bit quad-core processor, support for dual displays up to 4K resolution via a pair of micro-HDMI ports, Gigabit Ethe..
Arduino, emits red and green light. You can adjust the amount of each color using PWMThis module consists of a common cathode 3mm red/green LED and a 0Ω resistor, since operating voltage is 2.0v ~2.5v..
The TTP223 is a touch pad detector IC which offers 1 touch keyThe touching detection IC is designed for replacing traditional direct button key with diverse pad sizeLow power consumption and wide oper..
The Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straight forward to use. The two large exposed pads function ..
This simple board breaks out a micro-B USB connector’s VCC, GND, D- and D+ pins to a 0.1″ pitch header. If you want to add the increasingly popular micro-B USB to your project, but don’t want to put u..
6 x 6mm Button / Tact Switch Module for Plastic / GlassProduct Size (L x W x H): 6 x 3.7 x 0.8cmWarranty: 1 monthNote:Please allow 1-2mm errors due to manual measurementItem color displayed in photos ..
This module lowers the entrance voltage on specified output voltage that You adjust through trimmer on the board. It very practical because by changing entrance voltage, output voltage always stays th..
Main chip:LM393, Electret condenser microphone Working voltage: DC 4-6V Signal output indication Single channel signal output The output effective signal is low level When there is sound, outputs low ..
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiringAll pins of chip have been..
Working voltage: 2.5 V-5.5 VMaximum output power: 3 W x 2 (5 V 4 Ω)Length: 29 mmWidth: 20 mm● Note: please make sure the power supply is not more than 5.5V and please don't do reverse polarity for pos..
This module is based on principle of resistive voltage divider design, can make the red terminal connector input voltage to 5 times smaller(For )Arduino analog input voltages up to 5 v, the voltage de..
● Using original IRF520 power MOS tube, can adjust PWM output● Can let the Arduino drive up to 24V load, such as LED lights belt, DC motor, micro pump, solenoid valve● PWM can realize stepless dimming..
● Low power wireless module● Built-in 24GHz antenna use NRF24L01 chip from Nordic● 2.4 - 2.5GHz lisence-free ISM band● highest working data speed is 2Mbps● 125 channels can reach different point or ju..
The module is based on the 5528-photo resistor for the qualitative detection of ambient light intensity of electronic modulesPower Supply VCCMin: 2.7VTypical: 5VMax: 5.5VCurrent(@VCC=5V)Min: 0.5mAMax:..
This is a rain, plant leaf humidity sensor that can be used for all kinds of weather monitoringHigh quality FR-04 material, large area of 5.0*4.0cm, nickel plating surface has better oxidation resista..
Active Buzzer Module KY-012 Arduino module, it produces a single-tone sound when signal is high. To produce different tones, use the KY-006 Passive Buzzer moduleThe KY-012 Active Buzzer module consist..
Charger module for 3.7V lithium power (LiPo) packs which do not include their own protection circuitFeeds a 1A charge current to the battery and cuts off when a full charge is detected (4.2V)The charg..
Arduino Passive Piezoelectric Buzzer Module Keyes KY-006, it can produce a range of sound tones depending on the input frequencyThe KY-006 Buzzer Module consists of a passive piezoelectric buzzer, it ..
A 3.3V and
5V Breadboard Power Supply Module with series diode, polarity reversal
protection. The module can take 6.5V to 12V input and can produce 3.3V
and +5V. Can also output 5V on USB connec..
Imported normally open reed switchThe comparator output, the signal is clean, the waveform, driving ability, more than 15mA Operating voltage 3 3V-5VThe output in the form: Digital switching outputs 0..
Infrared obstacle avoidance sensor is designed for the design of a wheeled robot obstacle avoidance sensor distance adjustable. This ambient light sensor adaptable, high precision, having a pair of in..
This module is a switch that will turn on/off in the presence of a magnetic fieldThe KY-003 Hall Magnetic Sensor consists of a 3144EUA-S sensitive Hall-effect switch for high-temperature operation, a ..
Arduino IR Transmitter Module Keyes KY-005, emits infrared light at 38kHz. The KY-005 Infrared Transmitter Module consists of just a 5mm IR LED. It works together with the KY-022 IR receiver module. C..
Arduino Key Switch Module Keyes KY-004 is a push button that will output a high signal when pressedThe module consists of a FZ1713 tactile push button switch and a resistor. Compatible with popu..
The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP826..